Table of Contents
Disclaimer: This content is provided for educational and entertainment purposes only and does not constitute professional advice. We do not guarantee the accuracy or completeness of any information presented. We are not liable for any actions taken based on this content. For specific issues or decisions, we recommend seeking professional advice.
Introduction
Telehandlers are an essential part of any construction site or warehouse. They make moving heavy loads easy and efficient, but they also require regular maintenance to ensure they run smoothly and safely. One of the most important parts of telehandler tyre maintenance is keeping them properly inflated with the right pressure. Tyres that are underinflated will wear faster than those at their recommended pressure; conversely, overinflated tyres can wear out prematurely as well. To help you keep track of your tyre pressures and stay safe on the job site, here are some maintenace guide to telehandler tyres:
Inspection and Maintenance
- Check the tread depth. The tread is the part of a tyre where it makes contact with the ground and provides traction. Most manufacturers will recommend a minimum tread depth of 2 mm, as this helps to ensure that you have enough grip when driving over uneven terrain. If your tyres are below this threshold, they should be replaced immediately to avoid damaging your machine.
- Check tyre pressure regularly and keep it at or close to the recommended pressure (e.g., 80 kPa) for maximum performance and safety too low or too high can cause damage such as blowouts and sidewall punctures;
- Inspect for damage such as cuts, bulges, splits or cracks; if found replace immediately;
- Check for signs of wear and tear; if worn down more than 30% replace immediately; also check for damage caused by excessive use;
Tyre Care for the Off Season
- Check tyre pressure. If your telehandler’s tyres are not properly inflated, they can be damaged and cause the machine to move awkwardly, which can lead to accidents. To avoid this, check the pressure regularly throughout the year and make sure it remains consistent – ideally, you should aim for 30psi across all tyres at all times.
- Check for damage. You should inspect your telehandler’s tyres regularly to ensure that there are no defects or other damage that could cause it harm while in use (for example by causing them to blow up). If you find anything wrong with one of the tyres, get it replaced immediately before doing any work with it again – this will ensure that nobody gets hurt as a result of using an unsafe machine!
- Check for wear and tear (and cuts). Tyre life depends on many factors including terrain type and usage patterns, but generally speaking, there will come a time when each tyre needs replacing because they have worn down past their expected lifespan due to excessive use over time as well as general wear caused by normal day-to-day activities.
Checking for Wear and Tear
When checking for wear and tear, look for cuts, cracks and bulges in the tyre tread and sidewall. Make sure there is no damage to the tyre tread or sidewall. If there are signs of damage, it may be time to replace the tyre.
You will also want to check for uneven tyre wear. Each tyre is designed with a specific amount of tread on it so that you can drive safely on different surfaces without getting stuck or damaging your tyres too quickly. To check whether you need new tyres, measure out a straight line across each side of your tyres (make sure it isn’t too close to either edge). Then take another measurement in between those lines, this will show how much space is left before you hit an area where there’s no more rubber left.
Good Driving Habits
Drive in the same direction every time. Many drivers have a regular route that they follow, and this can be an effective way to maintain optimal tyre conditions.
Avoid sudden starts and stops. If you drive around using your telehandler, avoid sudden starts and stops; if possible, try to avoid braking too sharply as it may cause your tyres to wear too quickly or even puncture if you brake incorrectly. You should also avoid any other abrupt movements when operating the machine; for example, driving over potholes or other uneven surfaces can result in the tyres being damaged by sharp objects protruding from the road surface that damage the tread area of your tyres.
Proper Use of Attachments
Using attachments correctly is an integral part of machine safety. They should not be used to lift more weight than the tyre can handle, or to lift the telehandler off the ground.
Also, do not use attachments in wet conditions as this will drastically reduce grip and increase your chance of slipping or falling.
Rotating Tyres
Rotating tyres is important to ensure they wear evenly. It is recommended that you rotate your tyres every 5,000km, but if you don’t rotate them regularly, they will wear unevenly and have a shorter life span.
Conclusion
With the steps outlined above, you can be sure that your telehandler tyre maintenance will be handled safely and efficiently. By following these guidelines, you can be sure that your telehandler tyres will last a long time and provide a smooth ride for years to come.
Guest Author
Latest posts by Guest Author (see all)
- How to Personalise Your Own Funeral - January 8, 2026
- Child Custody Schedules by Age: A Realistic Guide for Australian Parents - November 17, 2025
- Unearthing the Intricacies of House Stump Replacement - October 3, 2025